Help
Both 2C and 4CR equipped markers:
Green (flashing) = Eyes on. No paintball staged in chamber.
White (flashing) = Eyes off.
Red (flashing) = Low Battery. Change battery immediately to avoid failure.
Orange (flashing) = Eye Malfunction. Most likely, paint from ball breaks
has blocked eye vision.
2C equipped markers:
Violet (flashing) = Bottom eye tripped. Paintball properly staged in
chamber.
4CR equipped markers:
Aqua (flashing) = Top eye tripped. Also use this to test top eye.
Blue (flashing) = Bottom eye tripped. Paintball properly staged in chamber.
To turn on the marker:
push marker on button momentarily
To Turn off the marker:
Turn marker off by pushing marker on button until the RED LED lights up, then release
program mode
1. Green: firing mode - 1=semi, 2=ramp, 3=3 shot, 4=full auto
2. Violet: Debounce - 1=1ms to 50=50mS
3. Aqua: Dwell - 4=4mS to 25=25mS
4. Blue: Ball in place delay - 1=off , 2=2mS, 5=5ms (slows marker ROF)
5. Red: Eye mode - 1=force, 2 delay, 3=eye off 19 BPS, 4=eye off 11 BPS
6. White ( all LEDs will turn on): ROF - 5 pulls=5 BPS cap all the way up to 19 pulls which=19 BPS; 20 pulls=unlimited ROF
To enable lock mode:
1. make sure the marker is off
2. push and hold the lock button
3. push marker on button
4. The RED LED will light up for 1.5sec
5. release lock button
6. LEDs will flash rapid rainbow of colors
7. Turn marker off by pushing marker on button until RED LED lights up, then release
To disable lock mode:
1. make sure the marker is off
2. push and hold the lock button
3. push marker on button
4. The GREEN LED will light up for 1.5sec
5. release lock button
6. LEDs will flash rapid rainbow of colors
7. Turn marker off by pushing marker on button until RED LED lights up, then release
To change/check the settings ( lock mode must be disabled)
1. make sure that the marker is off
2. pull trigger and hold
3. push marker on button
4. release both the on button and the trigger
5. LEDs will flash slow rainbow of colors
6. pull trigger to move between program modes (the LEDs will change
colors, you need to follow the color diagram in order to get to the right setting)
7. when you reach the desired program mode, pull the trigger and hold until the LED turns
off
8. 1 sec delay
9. BLUE LED will flash the current setting to you ( 1 flash is equal to one setting)
10.when the RED LED turns on, pull the trigger slowly until you reach your desired setting. Each trigger pull is going to cause the LED to
turn ORANGE.
10b. if you are just checking, do not touch the trigger; wait until 3 seconds until the RED LED to turn off.
11. After trigger pulls wait 3 sec for the RED LED to turn off.
12. BLUE LED will flash new setting
13. the marker will turn off after 1 sec and a dull RED LED will quickly flash
Cancel/ turn on "semi-only"
1.Turn on the marker
2.Pull Trigger and hold
3.Hold down lock button
4.Momentarily press power button and release
5.Aqua LED color will come on
6.Release trigger and lock button. Green LED
7.Slowly pull and release trigger 15 times. LED will flash orange with each pull
7b. if you are turning on the semi only mode, pull the trigger 13 times, instead.
8.If correct violet LED and board resets
Cancel/turn on the "no full-auto" mode
1.Turn on the marker
2.Pull Trigger and hold
3.Hold down lock button
4.press power button and release
5.Aqua LED will come on
6.Release trigger and lock button. Green LED will come on
7.Slowly pull and release trigger 15 times; LED will flash orange with each pull
7b. to turn the "no full-auto" mode, pull the trigger 10 times
8.If you did this corectly violet LED and board resets
To reset to factory settings:
1.Hold down lock button
2.Turn on marker
3.Continue holding lock button until the white LED turns on and then off (10sec)
4.Board turns off
This post has been edited by SKC: 22 June 2009 - 01:25 PM
