Special Ops Paintball: Build off thread help - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Build off thread help This will help with alot of questions Rate Topic: -----

#1 User is offline   blackrain 

  • Sophomore Member
  • PipPipPip
  • Group: Members
  • Posts: 524
  • Joined: 28-September 05
  • Gender:Male
  • Brigade Name:blackrain's aftermath

Posted 11 May 2009 - 10:50 AM

11 May 09:
This gun is long gone, but the refence is ther to help out others.
Later,
Blackrain:)




Well since no one bought this from me,I was forced to make a Sniper. Hope you enjoy. I'm still not finished with this project. I have to put in the Valve and then check the Velocity and shot count per 12 gram.
Later,
Blackrain


First you need to get everything ready.
Posted Image

After that you start the assembly process.
I installed the WWA "Dead Zone" devolumizer. This is suppose to bring the chamber back to
99" specs.
Posted Image

I removed the 15* ASA. I don't like these so I substituted it with a Black Vert ASA. The front block is also eliminated. (All originol parts will be sold with this project.) The ASA screw holds the "Dead Zone" in place.
Posted Image

Next put in the valve. I'm not sure of the type I put in,but it was free so who am I to complain.
Posted Image

Time for the IVG,hammer and spring. I usually drop the hammer in and run the cocking lug down a little so it catches. Next put in the spring and run down the IVG till you get a little tension. Adjustment isn't needed at this time. Proper timing and velocity will come later.
Posted Image

Now add the Vendetta pump guide. Inspect to make sure all threads are clean of burs and you have the oring. Tighten down with a cresent wrench
Posted Image

Next adjust the cocking rod. I usually leave this much thread when starting. This will come into play when the back block is added.
Posted Image

Next put the spring inside the pump handle and slide pump onto pump guide.
Posted Image

Now put on the back block and bolt with pin. Note how much thread I left. I had to back the block off a few turns. This gave me my needed clearance for the bolt. I'll do a finer adjustment once the whole thing is together.
Posted Image

Time to install the frame and trigger group. I'll be using an OMEGA roller trigger/sear set up. The frame is a WGP chrome that I got off ebay for cheap.
Posted Image

Next is the Beaver tail. Real cheap,I think I got it for free.
Posted Image

Let's try on the barrel. Had this WGP STO barrel laying around.
Posted Image

What the HELL,let's just add an SC feed.
Posted Image

Frame grips. Had these laying around too.
Posted Image

All that is left is to adjust the trigger,time the lug,put on the grips put in the rear cocking rod and add air. Unfortunatly,I'm going to run this on 12 gram and I don't have a quick change laying around. I'm also out of air. So I will continue this build when I can find a nice QC at a decent price.
Posted Image

Oh HELL while I'm at it I might as well change out the pump. I'm just going to use the Vendetta Deluxe pump. I have it laying around so why not.
Posted Image

Alright lets add a Quick change,new style beaver tail, and Rear cocking rod.
Posted Image

Alright so here it is. Almost complete. I have adjusted the trigger to my flavor. I'm waiting on one more part. That will be an AM Illusion 10 RND feed.
Posted Image

So I'm now adding a 99" valve and stem. This should help efficiency. Bought these from All American Paintball.
Posted Image
Posted Image

This post has been edited by blackrain: 11 May 2009 - 10:59 AM

0

#2 User is offline   shadow_772 

  • Never compromise, even in the face of armageddon
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 4,272
  • Joined: 05-September 05
  • Gender:Male
  • Location:MA
  • Brigade Name:Shadow_772

Posted 11 May 2009 - 10:53 AM

:tup:
0

#3 User is offline   blackrain 

  • Sophomore Member
  • PipPipPip
  • Group: Members
  • Posts: 524
  • Joined: 28-September 05
  • Gender:Male
  • Brigade Name:blackrain's aftermath

Posted 11 May 2009 - 10:55 AM

Check valve from WWA. I'm getting atleast 10 stored shots after CO2 ejection.
Posted Image

Also added an ANS slider frame.
Posted Image

The final results:
I only played with this one time, but it had a few upgrades done to it. I added a CCM pump handel and had the barrel bored out for freak inserts. Added a CCM frame and an aluminum stock.
Posted Image
Posted Image

This post has been edited by blackrain: 11 May 2009 - 10:54 AM

0

#4 User is offline   Sneaky Sir 

  • Studyin' my pump-fu
  • PipPipPipPip
  • Group: Members
  • Posts: 971
  • Joined: 23-June 06
  • Gender:Male
  • Location:Gibbon, MN
  • Brigade Name:Sneaky Sir

Posted 11 May 2009 - 01:40 PM

Linked it to this thread in my original post in the 09' Build-off thread
0

#5 User is offline   slowerpig81 

  • This man is a Beast with that Phantom. -thisissparta
  • PipPipPipPipPip
  • Group: Members
  • Posts: 1,528
  • Joined: 23-November 07
  • Gender:Male
  • Location:St. Louis, MO
  • Brigade Name:slowerpig81

Posted 11 May 2009 - 01:54 PM

Very nice. It's so much better with the CCM deluxe kit on there with AT and 86* frame, that just finishes it all off. While I know that it's not as light (the stroke) as CCMs because it's sprung for 12 grams, it still must be smooth as hell and I love CCM triggers. Add AT which is a very nice feature that adds user friendliness , and you have a great gun.
0

#6 User is offline   Legato 

  • AKA reapermen - AKA Legaqua - Resident Brass Whore
  • PipPipPipPipPipPipPip
  • Group: Retired/Inactive Moderator
  • Posts: 8,771
  • Joined: 02-February 05
  • Gender:Male
  • Location:Milford, Massachusetts

Posted 11 May 2009 - 10:02 PM

Sorry, we can't sticky posts in threads. Not in the forum software. Sorry. I can sticky the thread...that's about it. :panzer: *feels ashamed the software doesn't support the cool feature*

edit: oh and my name isn't sneaky. :)

This post has been edited by Legato: 11 May 2009 - 10:03 PM

"I think wearing camo is dishonorable. No honorable player would pretend to be a tree or bush."Posted Image My Gallery - Ninja/Pirate Alliance - Marker Animations Posted ImageSpec Ops Posted Image Pump CrewSig Rules - Gen Rules & Regs - Avatar Rules - Warn Level/Reduction - Forum FAQs - Ultimate Pump Sticky - PDT
0

#7 User is offline   Sneaky Sir 

  • Studyin' my pump-fu
  • PipPipPipPip
  • Group: Members
  • Posts: 971
  • Joined: 23-June 06
  • Gender:Male
  • Location:Gibbon, MN
  • Brigade Name:Sneaky Sir

Posted 12 May 2009 - 08:35 PM

Well lol you could make me a mod, then I could just sticky it myself :wub:
0

#8 User is offline   Legato 

  • AKA reapermen - AKA Legaqua - Resident Brass Whore
  • PipPipPipPipPipPipPip
  • Group: Retired/Inactive Moderator
  • Posts: 8,771
  • Joined: 02-February 05
  • Gender:Male
  • Location:Milford, Massachusetts

Posted 12 May 2009 - 10:23 PM

View PostSneaky Sir, on May 12 2009, 11:35 PM, said:

Well lol you could make me a mod, then I could just sticky it myself :wub:

If i had the power, and a nice gift wrapped piece of Brass, that might happen. Until then though...
"I think wearing camo is dishonorable. No honorable player would pretend to be a tree or bush."Posted Image My Gallery - Ninja/Pirate Alliance - Marker Animations Posted ImageSpec Ops Posted Image Pump CrewSig Rules - Gen Rules & Regs - Avatar Rules - Warn Level/Reduction - Forum FAQs - Ultimate Pump Sticky - PDT
0

#9 User is offline   Sneaky Sir 

  • Studyin' my pump-fu
  • PipPipPipPip
  • Group: Members
  • Posts: 971
  • Joined: 23-June 06
  • Gender:Male
  • Location:Gibbon, MN
  • Brigade Name:Sneaky Sir

Posted 13 May 2009 - 05:53 AM

The gift part may be plausable at the moment, but you need to get on your superiors and get that power.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users