[TS0716]

Ok, well i just went to the proshop and got my tank filled and the o-ring on the ram replaced, so the old leak problem is gone.

I took it out back, aired it up and dry fired for a little bit, no problems.

I put my hopper on it, turned it on, turned the eyes on and let it rip

It shot pretty consistently for about 20 shots, then the gun became stuck on full auto. It pretty much emptied the hopper, and left it like this



Once the balls stopped it feeding, it kept on shooting. I took the hopper off and checked the gun out. eyes were clear. The LPR was set to 75 psi, so i turned it down to 50. When i had it at 50, it sounded too quiet, as if it wasn't cycling fully. So i turned it up till it sounded normal, which was at 60 psi. I dry fired again, no problems. Put the hopper back on it with paint, started shooting, and it went full auto on me again until i pretty much ran out of air in the tank.

I have no clue what the problem could be. Last time i went to the field it shot fine. When i was shooting, it didn't look hot, but it may be the HPR is too high, but i don't have a gauge for it. I heard the LPR should be set for 50 psi on an infamous, but the gun just doesn't sound like it is cycling at 50 psi.

Here are my settings:

Debounce: 1
Dwell: 10
Anti-bounce: 3
ABS: 3

Virtue board btw. Any help would be appreciated.

[slinkyaroo]

First I will say - I've had 3 timmies and 2 DF's so this might sound funny but it's true....


Change the battery. other than that check the trigger and switch.



.

This post has been edited by slinkyaroo: 10 January 2008 - 02:36 PM

[TS0716]

haha. I took the battery out and put it back in a min later. now it works. thanks

board must have locked up

[The Hobbit]

you hopper looks yummy man. LOL

[blackraven64]

good luck with that hopper man.

halo disassembly ftl.

[slinkyaroo]

TS - your battery's cooked. 2K5 and up timmies are the only markers I know with this probalem - not DF's, 2K2 or any other markers.


I believe it's the required power to the noid since that draws the most power but I only have this problem on the field and with people that have no manual and have to figure things out but memeory. You're batteries done. Change it. Or bring a back up battery to the field.



.

This post has been edited by slinkyaroo: 10 January 2008 - 09:18 PM

[Marauder_Pilot]

blackraven64, on Jan 10 2008, 08:55 PM, said:

halo disassembly ftl.

Indeed. Those things suck, I can't wait until I've got the monies for a Magna.

This post has been edited by Marauder_Pilot: 11 January 2008 - 10:51 AM

[motoguy1251]

Man that hopper is taost.

Take electronics out and hose.

[TS0716]

hah that hopper was a pita to clean, but it got done. I got a new suicide shell in the mail while i was in the middle of cleaning it, so that was a plus.

I almost hosed it down, but i didn't wanna foul up the motor. I just used about half a roll of paper towels though. (sorry trees )

[willdunn]

I dont understand why your halo would do that, do you have an empire? its just weird that the balls would chop in the hopper like that...

willdunn

[SHADOW SNIPER]

hey bro long time no talk. well your batts. and your board is problly fried unless you really dont know how to change modes ad ur debounce higher idk but if someones that stupid u might think thats fully auto. anti bounce raise to 4-5 all i can think of this second besides why a timmy

[French]

willdunn, on Jan 26 2008, 11:41 PM, said:

I dont understand why your halo would do that, do you have an empire? its just weird that the balls would chop in the hopper like that...

willdunn

it a halo b eye's it sucks

[willdunn]

yea, but your paint would have to be pretty dark for it to do some thing like that

[kellts]

willdunn, on Jan 27 2008, 09:44 PM, said:

yea, but your paint would have to be pretty dark for it to do some thing like that

I'm with you. A Halo's eyes suck, but they suck at seeing movement. They don't have trouble with balls sitting in the stack..

It's gotta be a Reloader..

[Pirate]

You know, if you had a Pinokio hopper, that wouldn't be hard to clean at all.
(This is a plug for Pinokio hoppers).

Seeing as the problem has been solved, I'll only suggest you up the DeBounce a little.