Special Ops Paintball: Will a Tac 8 mag fit into a 8.1? - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Will a Tac 8 mag fit into a 8.1? Rate Topic: -----

#1 User is offline   Winchester 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 27-June 10

Posted 25 August 2010 - 02:20 PM

i already have two mags and i was thinking about getting a new gun. Thanks in advance
0

#2 User is offline   -SMITTY- 

  • one of the original 27,731 members
  • PipPipPipPipPip
  • Group: Members
  • Posts: 1,123
  • Joined: 20-January 07
  • Gender:Male
  • Location:You know Westfield MA? Nowhere near there. ;)
  • Brigade Name:-SMITTY-

Posted 25 August 2010 - 03:32 PM

Unfortunately, the T8 mags will not work in the T8.1. The barrel and parts of the mag are slightly different I think.

This post has been edited by -SMITTY-: 25 August 2010 - 04:25 PM

0

#3 User is offline   Winchester 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 27-June 10

Posted 25 August 2010 - 06:48 PM

damn. oh well. thanks smitty
0

#4 User is offline   coveringfire 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 95
  • Joined: 18-August 06
  • Gender:Male

Posted 25 August 2010 - 07:12 PM

it will, you just need a dremel. http://forums.tiberi...read.php?t=2720
Stalking since '06, Postin since '09, Playin since '04. Feedback
At my lemonade stand I used to give the first glass away free and charge five dollars for the second glass. The refill contained the antidote.
0

#5 User is offline   motherboard1 

  • Sophomore Member
  • PipPipPip
  • Group: Members
  • Posts: 359
  • Joined: 30-June 06

Posted 05 November 2010 - 08:25 AM

To save starting a new thread, I'll just ask my T 8.1 question here.

Can the rear block on the 8.1 come off, and the bolt be taken out and put back in without loosing off any of the body screws? I'd like the idea of being able to run a squeegie through the whole gun without much fuss.
0

#6 User is offline   sousey 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 228
  • Joined: 16-November 09
  • Gender:Male
  • Location:18073
  • Brigade Name:HELL-FIRE

Posted 06 November 2010 - 05:10 AM

View Postmotherboard1, on 05 November 2010 - 11:25 AM, said:

To save starting a new thread, I'll just ask my T 8.1 question here.

Can the rear block on the 8.1 come off, and the bolt be taken out and put back in without loosing off any of the body screws? I'd like the idea of being able to run a squeegie through the whole gun without much fuss.


- without fuss, NO!
- I'm not sure about 8.1 detents but the T8 can only be squeegeed in one direction (same direction as balls go).

This post has been edited by sousey: 06 November 2010 - 05:10 AM

0

#7 User is offline   motherboard1 

  • Sophomore Member
  • PipPipPip
  • Group: Members
  • Posts: 359
  • Joined: 30-June 06

Posted 06 November 2010 - 06:39 AM

Thanks for the reply but I'm not sure that was an answer.

I'm still trying to find out if the T8.1 allows the removal and insert of the bolt assembly without loosing off any body/regulator screws.

I'm making my final decision today on whether or not its worth it (to me) to buy a new 8.1, or a used 8.0.

Found my answer. and its No. The bolt out back doesn't do much for the design as you still need to take the lower receiver off and loose the regulator screw, just like the 8.0

This post has been edited by motherboard1: 06 November 2010 - 10:02 AM

0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users