Special Ops Paintball: Macro Lines and how to fit them to a gun. - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Macro Lines and how to fit them to a gun. Rate Topic: -----

#1 User is offline   lonestar2222003 

  • Sentinels Sniper
  • Pip
  • Group: Members
  • Posts: 24
  • Joined: 18-May 06
  • Gender:Male
  • Location:Minot ND
  • Brigade Name:The Sentinels

Posted 08 June 2010 - 09:07 AM

Im looking to buy the T2W air thru stock for my pump gun (V2 Classic Sniper) but the thing is i dont know how to use macro lines or how to fit them to the gun ive seen them done but dont really understand how they stay on with all that pressure.
If I miss you had better hope you can run 300 fps. O.S.O.K.

Team: The Sentinels

Organization: US Air Force

Sp-1 owner #28



0

#2 User is offline   ger 

  • Shine
  • PipPipPipPipPip
  • Group: Members
  • Posts: 1,676
  • Joined: 31-August 06
  • Gender:Male
  • Location:Western PA

Posted 08 June 2010 - 09:16 AM

View Postlonestar2222003, on Jun 8 2010, 12:07 PM, said:

Im looking to buy the T2W air thru stock for my pump gun (V2 Classic Sniper) but the thing is i dont know how to use macro lines or how to fit them to the gun ive seen them done but dont really understand how they stay on with all that pressure.


It's pretty simple & using them has basically become the standard for air lines. Some players still don't trust it & prefer using braided lines... to each their own. I've been using macro flawlessly for over 3 years now.

The macroline just slides into the macro fitting. The fitting has barbs on the inside that hold the line in place.
ger
You bought the brand, not my allegiance.
0

#3 User is offline   Tenacious221 

  • ELITE Member, now with matching elite patch!
  • PipPipPipPipPipPipPip
  • Group: Administrators
  • Posts: 10,087
  • Joined: 22-September 06
  • Gender:Male
  • Location:Kirkwood MO
  • Brigade Name:Tenacious221

Posted 08 June 2010 - 09:17 AM

You can just slide them into the fittings and they're good to go.

Be sure to cut sleightly LONGER than you need and then trim down gradually. You can always cut shorter, but you can't make the macroline longer.

(As a side note: The T2W should come with quite a bit of macroline in the box for you)

-Tenacious
0

#4 User is offline   5N1P3R 

  • Master Member
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,832
  • Joined: 24-August 08
  • Gender:Male
  • Location:Minnesota

Posted 08 June 2010 - 09:18 AM

You attach them to 90 degree macro fittings in most cases. It is quite simple, you just push them in until you feel a sort of click. To take them out, you push them in and they slide out. And then hold. Make sure that the macroline is long enough, AND that the end is flat, not jagged.

Someone will come in and post a better explanation.

Edit: I thought I was posting first :P

This post has been edited by 5N1P3R: 08 June 2010 - 09:19 AM

0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users