Special Ops Paintball: Spyder MR1 - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Spyder MR1 Problem with cocking Rate Topic: -----

#1 User is offline   txhazard 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 50
  • Joined: 08-March 09
  • Gender:Male
  • Location:Wylie, Tx

Posted 28 April 2010 - 05:23 PM

Figured id bring the problem here and see what i can do to fix it.

When i cock the gun it fires, but then uncocks and needs to be cocked again after the first fire. Also the ball that comes out is really really weak.

thx advance.
"Molon Labe"
0

#2 User is offline   Soyeahwatsup 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 123
  • Joined: 05-February 10
  • Gender:Male
  • Location:Palm Beach Country, FL
  • Brigade Name:SGTWHITEY

Posted 28 April 2010 - 06:14 PM

Is the mr1 mechanical because if so check your springs one of them might be weak or broken. Or your low on co2 or hpa. But take your marker apart and check for anything damaged or something thats not supposed to be in there
0

#3 User is offline   txhazard 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 50
  • Joined: 08-March 09
  • Gender:Male
  • Location:Wylie, Tx

Posted 29 April 2010 - 06:11 PM

View PostSoyeahwatsup, on Apr 28 2010, 06:14 PM, said:

Is the mr1 mechanical because if so check your springs one of them might be weak or broken. Or your low on co2 or hpa. But take your marker apart and check for anything damaged or something thats not supposed to be in there



Everything seems good, im may have to just goto the proshop.
"Molon Labe"
0

#4 User is offline   Soyeahwatsup 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 123
  • Joined: 05-February 10
  • Gender:Male
  • Location:Palm Beach Country, FL
  • Brigade Name:SGTWHITEY

Posted 29 April 2010 - 07:08 PM

This sounds like a dumb question but did you try to turn the velocity up?
0

#5 User is offline   txhazard 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 50
  • Joined: 08-March 09
  • Gender:Male
  • Location:Wylie, Tx

Posted 30 April 2010 - 05:09 PM

View PostSoyeahwatsup, on Apr 29 2010, 07:08 PM, said:

This sounds like a dumb question but did you try to turn the velocity up?



Not a dumb question, is the velocity the small gold screw under the gun? Cause it fireing again but not givving of alot of air at all. Eureka i think that might be the problem, YAY FOR DUMB QUESTIONS!
"Molon Labe"
0

#6 User is offline   Down Range Pain 

  • Holy Necropost Batman!
  • PipPipPip
  • Group: Members
  • Posts: 466
  • Joined: 01-March 10
  • Gender:Male
  • Location:254 Texas

Posted 13 May 2010 - 05:23 AM

Quote

Not a dumb question, is the velocity the small gold screw under the gun? Cause it fireing again but not givving of alot of air at all. Eureka i think that might be the problem, YAY FOR DUMB QUESTIONS!



no the velocity adjuster is the screw on the back,of the black plug,on the back of ur gun. the on the caps off the lower chamber from the rear and holds a sping.

This post has been edited by Down Range Pain: 13 May 2010 - 05:23 AM

Returning hate for hate multiplies hate, adding deeper darkness to a night already devoid of stars. Darkness cannot drive out darkness: only light can do that. Hate cannot drive out hate: only love can do that.” --Martin Luther King Jr.

"Victory is a very dangerous oppertunity" --General Andre Beaufre
0

#7 Guest_Schecter_*

  • Group: Guests

Posted 21 May 2010 - 05:37 PM

View Posttxhazard, on Apr 28 2010, 05:23 PM, said:

Figured id bring the problem here and see what i can do to fix it.

When i cock the gun it fires, but then uncocks and needs to be cocked again after the first fire. Also the ball that comes out is really really weak.

thx advance.


Raise the pressure. Your gun doesn't have enough pressure to push the striker back. Try with paint, if the paintballs roll out of the tip of your barrel that may be your problem, if it will fully shoot that means you don't have enough air going to the striker because it's all going to firing the paintball.

If and ONLY IF it is firing the paintball at 300fps or close and not cocking you may have to get more air into the striker area. This can be accomplished by putting another groove on the valve pin. Take a dremmel and on the opposite side make a groove like the one on the top. Don't go nuts, a little goes a long way.
should look like this when you're done
Posted Image
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users