Special Ops Paintball: What's stopping me from - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

What's stopping me from another polishing internals thread!

#1 User is offline   The_Red 

  • The Irish Sabre
  • PipPip
  • Group: Members
  • Posts: 95
  • Joined: 07-July 08
  • Gender:Male
  • Location:Georgia
  • Brigade Name:The_Red

Posted 28 December 2010 - 06:41 PM

so, does anyone else think i could use a wire brush on my power drill and polish my internals that way? I mean, i used the same rig to clean the metal of the engine compartment on my first car, so does anyone think that it'll work on my A5?
a lot of speedballers haven't realized that their $500+ guns can, in fact fire one round at a time.
0

#2 User is offline   Down Range Pain 

  • Holy Necropost Batman!
  • PipPipPip
  • Group: Members
  • Posts: 466
  • Joined: 01-March 10
  • Gender:Male
  • Location:254 Texas

Posted 28 December 2010 - 08:25 PM

little extreme...if i did tht i would do it very carefully
Returning hate for hate multiplies hate, adding deeper darkness to a night already devoid of stars. Darkness cannot drive out darkness: only light can do that. Hate cannot drive out hate: only love can do that.” --Martin Luther King Jr.

"Victory is a very dangerous oppertunity" --General Andre Beaufre
0

#3 User is offline   Legato 

  • AKA reapermen - AKA Legaqua - Resident Brass Whore
  • PipPipPipPipPipPipPip
  • Group: Retired/Inactive Moderator
  • Posts: 8,771
  • Joined: 02-February 05
  • Gender:Male
  • Location:Milford, Massachusetts

Posted 28 December 2010 - 11:57 PM

Wire brush is a bit too abrassive to me. I'd just stick with 0000 grade steel wool. You aren't trying to remove any material, just overspray.
"I think wearing camo is dishonorable. No honorable player would pretend to be a tree or bush."Posted Image My Gallery - Ninja/Pirate Alliance - Marker Animations Posted ImageSpec Ops Posted Image Pump CrewSig Rules - Gen Rules & Regs - Avatar Rules - Warn Level/Reduction - Forum FAQs - Ultimate Pump Sticky - PDT
0

#4 User is offline   druid 

  • Celtic Warrior - Mo Anam Cara
  • PipPipPipPipPip
  • Group: Members
  • Posts: 2,420
  • Joined: 24-March 05
  • Gender:Male
  • Location:610 PA
  • Brigade Name:druidsdecendant

Posted 29 December 2010 - 03:42 AM

Use the gray rubber wheel of the Dremel. Works for me
Warped A5; M98; 68 Magnum w/ AGD 6-Pack, Automaggot #92 Custom Modder #5
"Political correctness is a doctrine, fostered by a delusional, illogical minority, and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
I got my OWN smiley...
0

#5 User is offline   Krazy8 

  • User Defined
  • PipPipPipPipPipPip
  • Group: Retired/Inactive Moderator
  • Posts: 2,555
  • Joined: 30-January 05
  • Gender:Male
  • Location:Rathdrum , ID
  • Brigade Name:Krazy8

Posted 29 December 2010 - 09:36 AM

I used a dremel and a brass brush once to remove the oversprayed powdercoat on an A5.

But a standard steel brush on a dower drill is going to mar the cast aluminum more than polish. Although it will be a uniform marring...


Do as the above posters mentioned and attack the job by hand with steel wool or with a polishing kit for the dremel.

This post has been edited by Krazy8: 29 December 2010 - 09:36 AM

0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users