Special Ops Paintball: 4.0 Frenzy Board Instructions - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

4.0 Frenzy Board Instructions For Bob Long Protege

#1 User is offline   SKC 

  • So Others May Live.
  • PipPipPip
  • Group: Members
  • Posts: 395
  • Joined: 01-August 05
  • Gender:Male
  • Location:The oregon dunes
  • Brigade Name:SKC 1.5

Posted 22 June 2009 - 01:17 PM

This is for People, like me, that bought a Protege and got a board with a single button. This board is not bad, it is the new 4.0 frenzy board. In this thread, I will explain how to change the setting on the board, since Bob Long did not update his online manuals.


Both 2C and 4CR equipped markers:

Green (flashing) = Eyes on. No paintball staged in chamber.
White (flashing) = Eyes off.
Red (flashing) = Low Battery. Change battery immediately to avoid failure.
Orange (flashing) = Eye Malfunction. Most likely, paint from ball breaks
has blocked eye vision.

2C equipped markers:
Violet (flashing) = Bottom eye tripped. Paintball properly staged in
chamber.

4CR equipped markers:
Aqua (flashing) = Top eye tripped. Also use this to test top eye.
Blue (flashing) = Bottom eye tripped. Paintball properly staged in chamber.

To turn on the marker:
push marker on button momentarily

To Turn off the marker:
Turn marker off by pushing marker on button until the RED LED lights up, then release

program mode
1. Green: firing mode - 1=semi, 2=ramp, 3=3 shot, 4=full auto
2. Violet: Debounce - 1=1ms to 50=50mS
3. Aqua: Dwell - 4=4mS to 25=25mS
4. Blue: Ball in place delay - 1=off , 2=2mS, 5=5ms (slows marker ROF)
5. Red: Eye mode - 1=force, 2 delay, 3=eye off 19 BPS, 4=eye off 11 BPS
6. White ( all LEDs will turn on): ROF - 5 pulls=5 BPS cap all the way up to 19 pulls which=19 BPS; 20 pulls=unlimited ROF


To enable lock mode:
1. make sure the marker is off
2. push and hold the lock button
3. push marker on button
4. The RED LED will light up for 1.5sec
5. release lock button
6. LEDs will flash rapid rainbow of colors
7. Turn marker off by pushing marker on button until RED LED lights up, then release


To disable lock mode:
1. make sure the marker is off
2. push and hold the lock button
3. push marker on button
4. The GREEN LED will light up for 1.5sec
5. release lock button
6. LEDs will flash rapid rainbow of colors
7. Turn marker off by pushing marker on button until RED LED lights up, then release


To change/check the settings ( lock mode must be disabled)
1. make sure that the marker is off
2. pull trigger and hold
3. push marker on button
4. release both the on button and the trigger
5. LEDs will flash slow rainbow of colors
6. pull trigger to move between program modes (the LEDs will change
colors, you need to follow the color diagram in order to get to the right setting)
7. when you reach the desired program mode, pull the trigger and hold until the LED turns
off
8. 1 sec delay
9. BLUE LED will flash the current setting to you ( 1 flash is equal to one setting)
10.when the RED LED turns on, pull the trigger slowly until you reach your desired setting. Each trigger pull is going to cause the LED to
turn ORANGE.
10b. if you are just checking, do not touch the trigger; wait until 3 seconds until the RED LED to turn off.
11. After trigger pulls wait 3 sec for the RED LED to turn off.
12. BLUE LED will flash new setting
13. the marker will turn off after 1 sec and a dull RED LED will quickly flash


Cancel/ turn on "semi-only"
1.Turn on the marker
2.Pull Trigger and hold
3.Hold down lock button
4.Momentarily press power button and release
5.Aqua LED color will come on
6.Release trigger and lock button. Green LED
7.Slowly pull and release trigger 15 times. LED will flash orange with each pull
7b. if you are turning on the semi only mode, pull the trigger 13 times, instead.
8.If correct violet LED and board resets


Cancel/turn on the "no full-auto" mode
1.Turn on the marker
2.Pull Trigger and hold
3.Hold down lock button
4.press power button and release
5.Aqua LED will come on
6.Release trigger and lock button. Green LED will come on
7.Slowly pull and release trigger 15 times; LED will flash orange with each pull
7b. to turn the "no full-auto" mode, pull the trigger 10 times
8.If you did this corectly violet LED and board resets


To reset to factory settings:
1.Hold down lock button
2.Turn on marker
3.Continue holding lock button until the white LED turns on and then off (10sec)
4.Board turns off

This post has been edited by SKC: 22 June 2009 - 01:25 PM

I proudly endorse:
Bob Long Markers - Empire Loaders and Apparel- Hybrid Apparel - Ninja Air Systems - VForce Masks


U.S. Navy AIRR
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users