Special Ops Paintball: PMR help - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

PMR help it leaks

#1 User is offline   Bobbjoe 

  • Group: Banned
  • PipPipPipPip
  • Group: Members
  • Posts: 798
  • Joined: 14-August 07
  • Gender:Male
  • Location:McKinney, Texas
  • Brigade Name:Bobbjoe

Posted 21 December 2008 - 10:20 PM

My pmr which is about 4 weeks old has just started leaking out of an area around the trigger. The leak is hardly noticeable, and the gun still works fine, but I'm kind of worried about it. I have only made slight velocity adjustments, so I'm sure that I have not blown the solenoid by over pressurizing it. Anyone have any idea whats going on?


Also, I've tried replacing many of the O rings in the bolt.

I Choose not to Conform to the Stereotypical Conformities that Stereotypical Conformative Society Conforms to.
What now?
0

#2 User is offline   Phantom9399 

  • Ninja!
  • PipPip
  • Group: Members
  • Posts: 153
  • Joined: 28-January 06
  • Gender:Male
  • Location:United States
  • Brigade Name:Phantom9399

Posted 23 December 2008 - 01:49 PM

when you take the bolt out, there is an o-ring that's almost on the bottom... its on the vent that the air comes into the bolt, did you replace that one?

if you go to actionvillage there is a complete o-ring kit for the PMR for only 7 or 8 dollars... i would just replace every o-ring cause the kit is so cheap

here is a link...

http://www.actionvil...om/011-269-0146
One shot = One kill
"As i walk through the valley of the shadow of death i am not afraid because i am the meanest motherBOINKer in the whole valley" - General Patton
Tippmann owner # 98
JT owner number 5
0

#3 User is offline   Bobbjoe 

  • Group: Banned
  • PipPipPipPip
  • Group: Members
  • Posts: 798
  • Joined: 14-August 07
  • Gender:Male
  • Location:McKinney, Texas
  • Brigade Name:Bobbjoe

Posted 23 December 2008 - 02:45 PM

View PostPhantom9399, on Dec 23 2008, 02:49 PM, said:

when you take the bolt out, there is an o-ring that's almost on the bottom... its on the vent that the air comes into the bolt, did you replace that one?

if you go to actionvillage there is a complete o-ring kit for the PMR for only 7 or 8 dollars... i would just replace every o-ring cause the kit is so cheap

here is a link...

http://www.actionvil...om/011-269-0146



Yeah, i did replace that one.

So i just took the solenoid out to relube its seat. The leak got bigger when i screwed it back in, so i think its the rubber seal that it sits on that's the problem.

I Choose not to Conform to the Stereotypical Conformities that Stereotypical Conformative Society Conforms to.
What now?
0

#4 User is offline   Phantom9399 

  • Ninja!
  • PipPip
  • Group: Members
  • Posts: 153
  • Joined: 28-January 06
  • Gender:Male
  • Location:United States
  • Brigade Name:Phantom9399

Posted 17 January 2009 - 09:18 PM

it might be the rubber seal

just make sure your eye wire isnt pinched anywhere and its where it should be

other than that, i dunno how to help
One shot = One kill
"As i walk through the valley of the shadow of death i am not afraid because i am the meanest motherBOINKer in the whole valley" - General Patton
Tippmann owner # 98
JT owner number 5
0

#5 User is offline   Bobbjoe 

  • Group: Banned
  • PipPipPipPip
  • Group: Members
  • Posts: 798
  • Joined: 14-August 07
  • Gender:Male
  • Location:McKinney, Texas
  • Brigade Name:Bobbjoe

Posted 19 January 2009 - 07:11 PM

I sent it into proto.. three weeks ago.. Does anyone know the normal turn around time for repair?

I Choose not to Conform to the Stereotypical Conformities that Stereotypical Conformative Society Conforms to.
What now?
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users