Special Ops Paintball: cant slow me down - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

cant slow me down Velocity Rate Topic: -----

#1 User is offline   sau4u 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 15
  • Joined: 03-May 09

Posted 26 June 2009 - 01:36 PM

Hey guys, here is whats happening to me. I have four alpha black bravo ones. All have the JCS power tube, howitzer front bolt and ACT installed. All have the egrip. My kids and I have used them about 3 times. On one of the guns no matter how far I screw in the velocity screw I cant slow the gun down lower than 310FPS. The field I play on has a 275 limit. Anyone have any suggestions on what I could do. Thanks. NOTE: I also use HPA, I tried CO2 for the heck of it with no change.
0

#2 User is offline   KRA SHARPSHOOTER 

  • [ Doglegs of War ] ~Silent But Deadly~
  • PipPipPip
  • Group: Members
  • Posts: 422
  • Joined: 18-August 07
  • Gender:Male
  • Location:New Prague, MN
  • Brigade Name:KRA SHARPSHOOTER

Posted 26 June 2009 - 01:45 PM

Here are two options to try:
- Clip your Drive Spring; This will result in less force being used to open the Valve, and consequently you will have less air being released. *This is not reversible*
- Acquire a spring kit; this will enable you to choose from a variety springs, and find one that is lighter than the stock one which will lower your velocity.

KRA SHARPSHOOTER's A-5 - [ Doglegs of War ] - ~Silent But Deadly~ - Archive of Wisdom - Online Discount Codes
"I don't play Woodsball because I have an A-5, I have an A-5 because I play Woodsball" - KRA SHARPSHOOTER
0

#3 User is offline   Thalion 

  • Probably in the Shooters Thread...
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,984
  • Joined: 22-January 06
  • Gender:Male
  • Location:Twin Cities, MN

Posted 26 June 2009 - 01:48 PM

Spring kit is the best choice.
Member of Team Akkadian

0

#4 User is offline   Puzuma 

  • That is not dead which can eternal lie,
  • PipPipPipPipPipPipPip
  • Group: Administrators
  • Posts: 14,382
  • Joined: 22-September 06
  • Gender:Male
  • Location:London ON, Canada
  • Brigade Name:Puzuma

Posted 26 June 2009 - 01:49 PM

If you choose to clip the spring, only clip a 1/4 coil at a time. It's easier to clip a bunch of small pieces than to put a large one back on....
Posted Image
That is not dead which can eternal lie,And with strange aeons even death may die.
0

#5 User is offline   Droop 

  • Professional Noobsmith
  • PipPipPipPipPip
  • Group: Members
  • Posts: 1,683
  • Joined: 11-December 05
  • Gender:Male
  • Location:McKinleyville CA
  • Brigade Name:Droopy Squirrel

Posted 26 June 2009 - 02:40 PM

or better buy a reg for it and take down the input pressure
Droop

My Feedback Member of Garage Inc. Official Pump User #100 Automaggot #91
My Trigger SC Feed comma club member #6

So because I play scenarios, I won't buy a high-end unless it has rails at useless angles, and has a machine-gun shroud bolted on it?-Maduce
0

#6 User is offline   sau4u 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 15
  • Joined: 03-May 09

Posted 27 June 2009 - 01:11 PM

For all that is interested, I got my problem fixed. It was the ACT upgrade. I removed the ACT, put it back to stock and all my velocity issues are cured. Later
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users