Special Ops Paintball: help.... - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

help.... I have such bad luck Rate Topic: -----

#1 User is offline   Locknpump 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 111
  • Joined: 14-January 11

Posted 05 February 2011 - 03:20 PM

Finally get my 48/3k tank aired, get home to try it out and get its velocity adjusted...but every two shots after the ball left it would just let air continue to run through, whats going on? And it went empty after like 75-100 shots
0

#2 User is offline   mike7822 

  • Aloha!
  • PipPipPipPip
  • Group: Members
  • Posts: 946
  • Joined: 26-September 07
  • Gender:Male
  • Location:United States
  • Brigade Name:MIKE7822

Posted 05 February 2011 - 03:42 PM

View PostLocknpump, on 05 February 2011 - 05:20 PM, said:

Finally get my 48/3k tank aired, get home to try it out and get its velocity adjusted...but every two shots after the ball left it would just let air continue to run through, whats going on? And it went empty after like 75-100 shots


What type of pump is it?
You probably need to lube/oil the valve.

This post has been edited by mike7822: 05 February 2011 - 03:42 PM

03 Prostock Pump ♦ 08 Ego
0

#3 User is offline   Locknpump 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 111
  • Joined: 14-January 11

Posted 05 February 2011 - 05:03 PM

its a 2005 prostock pump, has a black magic regulator on it (I believe). Or it's stock one.

and it only happens when I use HPA not co2

This post has been edited by Locknpump: 05 February 2011 - 05:03 PM

0

#4 User is offline   mike7822 

  • Aloha!
  • PipPipPipPip
  • Group: Members
  • Posts: 946
  • Joined: 26-September 07
  • Gender:Male
  • Location:United States
  • Brigade Name:MIKE7822

Posted 05 February 2011 - 06:13 PM

IIRC:
The HPA's output pressure is lower than C02, and then it cannot create a seal in the valve. So, to fix this you need to lubricate the valve (lower tube of the autococker) and/or change O-rings out. To do this you need to take the frame off, take the pump, pump arm, backblock, bolt and frame off. You also need a valve tool, if you do not have one.
03 Prostock Pump ♦ 08 Ego
0

#5 User is offline   Locknpump 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 111
  • Joined: 14-January 11

Posted 06 February 2011 - 03:20 PM

cleaned the entire marker spotless...tried using co2 and it leaked through the barrel after every shot, so im guessing there is something wrong with the valve, I dont understand why this marker is so touchy >.>
0

#6 User is offline   Krazy8 

  • User Defined
  • PipPipPipPipPipPip
  • Group: Retired/Inactive Moderator
  • Posts: 2,555
  • Joined: 30-January 05
  • Gender:Male
  • Location:Rathdrum , ID
  • Brigade Name:Krazy8

Posted 07 February 2011 - 11:47 AM

Previous owner abuse...or current user abuse.
0

#7 User is offline   mike7822 

  • Aloha!
  • PipPipPipPip
  • Group: Members
  • Posts: 946
  • Joined: 26-September 07
  • Gender:Male
  • Location:United States
  • Brigade Name:MIKE7822

Posted 07 February 2011 - 02:04 PM

Posted Image

In the bottom right corner of the diagram is the valve. There should be 2-3 O-rings on the valve, put lube on them. Also, check to see if the bolt is in right, the hole is the bolt should point down. Also, lube the bolt's O-rings. IF you are putting in back together, then krazy was right.


They got rid of the WGP website and the wonderful cocker diagram they had on it :(
03 Prostock Pump ♦ 08 Ego
0

#8 User is offline   Locknpump 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 111
  • Joined: 14-January 11

Posted 07 February 2011 - 05:53 PM

The gun has been put together and cleaned perfectly, Ive ordered a valve tool (holy expensiveness) and a new valve. Hopefully they will be here thursday. My guess is that the o-rings are done for and the valve has some good wear on it so im just replacing the whoie thing.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users