Special Ops Paintball: Ion leaking - Special Ops Paintball

Jump to content


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Ion leaking need some input

#1 User is offline   Aych 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 92
  • Joined: 11-August 07
  • Gender:Male
  • Location:Flake, MN
  • Brigade Name:Aych

Posted 18 October 2008 - 12:47 PM

ok my ion is leaking as i can hear i had to replace the banjo fittings recently and i'm still hearing some leaks on the gun(orange)Attached File  ion_troble.JPG (96.31K)
Number of downloads: 27
can anyone help me?

This post has been edited by Aych: 18 October 2008 - 12:47 PM

0

#2 User is offline   Kodiak 

  • Captain DHP
  • PipPipPipPip
  • Group: Members
  • Posts: 821
  • Joined: 28-January 05
  • Gender:Male
  • Location:Fayetteville, NC
  • Brigade Name:Kodiak

Posted 18 October 2008 - 12:53 PM

Ion Owners Group

Follow these direction to pin-point the leak.

Step 1 : Disassemble the marker. Separate the trigger frame from the firing assembly. Remove the battery, eye board, eye wires, body shell.

Step 2 : With the shell still off, reconnect the mid banjo or qev to the breech and reconnect the rear banjo to the donut. With the trigger frame still separate from the firing assembly, reconnect the front banjo to the trigger frame ASA port.

Step 3 : Turn down your reg and air up the ION. Increase the pressure to about 100psi.

Step 4 : Listen for the general area that the leak is coming from. Mix a bowl of 25% dish soap and 75% water and apply it to the leak area with a q-tip. Bubbles will form at the exact point where air is escaping.

If the leak stopped with the firing assembly off the frame, the common cause is bad hoses. Try gently pulling and pushing on hoses to try to determine which hose is causing the leak.

It is common for the frame to push on the rear banjo when it's assembled, causing the rear banjo to leak.Try shortening the rear hose by 1mm. Make sure the cut is clean and straight. If you still have it, try replacing the rear hose with the spare hose that came with your Ion. Also, you can try swapping the rear banjo with the front banjo.
0

#3 User is offline   Tora 

  • Yes, that is Barney. My Barney. No you can't have him.
  • PipPipPip
  • Group: Members
  • Posts: 628
  • Joined: 24-November 06
  • Gender:Male
  • Location:My mommy

Posted 18 October 2008 - 12:57 PM

Replace your in gun hoses.
My ion had a small leak,I thought it was a banjo but it turned out to be a small slice in the hose where it connects to the rear banjo.
hope it helps!

Tora
FEEDBACK

My momma raised me the be SHAMELESS!
0

#4 User is offline   druid 

  • Celtic Warrior - Mo Anam Cara
  • PipPipPipPipPip
  • Group: Members
  • Posts: 2,420
  • Joined: 24-March 05
  • Gender:Male
  • Location:610 PA
  • Brigade Name:druidsdecendant

Posted 18 October 2008 - 09:15 PM

In the pic he's got an orange "O" around the macroline fitting. and an orange "X" on what looks like the feedneck port.

It's leaking because:

1. "O" = That weird bend you have in the line. Make it straight instead of an "S"
2. "O" = Make sure the end of that line is cut STRAIGHT...as in, a 90* cut to the wall of the line.
3. "X" = Forward bolt ORing is either damaged or needs grease
4 ."X" = SFT Oring inside the chamber is damaged or needs grease

Or your psi is too high, forcing it out those areas.
Warped A5; M98; 68 Magnum w/ AGD 6-Pack, Automaggot #92 Custom Modder #5
"Political correctness is a doctrine, fostered by a delusional, illogical minority, and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
I got my OWN smiley...
0

#5 User is offline   the eggman 

  • ninjadodjy is always watching you...
  • PipPipPipPip
  • Group: Members
  • Posts: 778
  • Joined: 29-May 08
  • Gender:Male
  • Location:cinci, oh
  • Brigade Name:bake-bake

Posted 28 October 2008 - 08:15 PM

when ever my ion leaks there it is usually the macro but that is just me. or i need to bust out the teflon.... WHABLAM!
0

#6 User is offline   dagger boy 98c 

  • Expect the unexpected
  • PipPipPip
  • Group: Members
  • Posts: 309
  • Joined: 15-July 06
  • Gender:Male
  • Brigade Name:dagger boy 98c

Posted 04 November 2008 - 12:52 PM

as every one has stated, replace that macro elbo and then also replace your orings.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users