Special Ops Paintball: T9 Leaking after a teardown - Special Ops Paintball

Jump to content


  • (2 Pages)
  • +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

T9 Leaking after a teardown Rate Topic: -----

#1 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 05:30 PM

Hi,

Just got my T9 the other day and had a breakage so I took apart cleaned and put back together....

When I put a mag in after all the air just came out the back of the gun and out the regulator adjustment hole.

Ive tried putting the bold forward and checked the o rings and have had no luck...

Any ideas?

Thanks
Josh
0

#2 User is offline   jim762 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 171
  • Joined: 30-September 08
  • Gender:Male
  • Location:lemoore, Ca
  • Brigade Name:jim762

Posted 26 January 2009 - 05:42 PM

Check your o rigs in your regulator and relief valve. Check out the tiberius forum for some ideas. http://forums.tiberiusarms.com/

May God have mercy upon my enemies, because I won't!
Sponsored by: Urban Ops Armory
0

#3 User is offline   Jackson 

  • Resident Tiberius Expert
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,947
  • Joined: 01-February 05
  • Gender:Male
  • Location:Pittsburgh, PA
  • Brigade Name:PvtDBJackson

Posted 26 January 2009 - 05:44 PM

View Postjoshnz, on Jan 26 2009, 07:30 PM, said:

Hi,

Just got my T9 the other day and had a breakage so I took apart cleaned and put back together....

When I put a mag in after all the air just came out the back of the gun and out the regulator adjustment hole.

Ive tried putting the bold forward and checked the o rings and have had no luck...

Any ideas?

Thanks
Josh

Sounds like you are missing the o-ring between the regulator/trigger block and the engine and firing bolt assembly. It's o-ring #13 on page 10 of the Manual here: http://www.tiberiusarms.com/documents/manu...nual_May_08.pdf
0

#4 User is offline   82ndx 

  • Facta Non Verba
  • PipPip
  • Group: Members
  • Posts: 220
  • Joined: 13-January 07
  • Gender:Male
  • Location:Surrey, BC
  • Brigade Name:82ndx

Posted 26 January 2009 - 06:26 PM

Not a T9 owner but definitely sounds like an O-Ring problem as these gents have said.
0

#5 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 07:08 PM

Yes, it is indeed that o-ring between the regulator/trigger block and the engine and firing bolt assembly.

Seems that me being the impatiant person that I am, did things to quickly and it is on my floor ^_^

now i need to find it hehe,

Thanks
Josh
0

#6 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 07:31 PM

Ok so the air doesnt leak any more but now when i put the mag in and press the trigger nothing happens.

But when I eject the mag I get an unnormal amount of co2 pushing it out.

Any ideas on this one?
0

#7 User is offline   jim762 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 171
  • Joined: 30-September 08
  • Gender:Male
  • Location:lemoore, Ca
  • Brigade Name:jim762

Posted 26 January 2009 - 07:34 PM

Did you push the bolt forward before you put it back together?

May God have mercy upon my enemies, because I won't!
Sponsored by: Urban Ops Armory
0

#8 User is offline   Jackson 

  • Resident Tiberius Expert
  • PipPipPipPipPipPip
  • Group: Members
  • Posts: 2,947
  • Joined: 01-February 05
  • Gender:Male
  • Location:Pittsburgh, PA
  • Brigade Name:PvtDBJackson

Posted 26 January 2009 - 07:41 PM

View Postjim762, on Jan 26 2009, 09:34 PM, said:

Did you push the bolt forward before you put it back together?


^^^^ This.

Make sure the bolt is well forward of the sear before putting the trigger assembly back on.
0

#9 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 08:17 PM

Hehe, silly me ^_^

That was it, gun back up and running.

Thankyou guys and gals
0

#10 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 11:22 PM

Another problem now....

I think I have blown and O-ring, It fires once then empties all the rest of the co2,

Which O-ring would I have blown?
0

#11 User is offline   jim762 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 171
  • Joined: 30-September 08
  • Gender:Male
  • Location:lemoore, Ca
  • Brigade Name:jim762

Posted 26 January 2009 - 11:25 PM

depends on where it is leaking from....not really sure about that one..sorry

May God have mercy upon my enemies, because I won't!
Sponsored by: Urban Ops Armory
0

#12 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 26 January 2009 - 11:26 PM

Oh yea, sorry its leaking out of the barrel.

Ive checked the o-ring in the air chamber and the lubed up the bolt.

Leaking quietly though the barrel and not fireing.

This post has been edited by joshnz: 27 January 2009 - 12:09 AM

0

#13 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 27 January 2009 - 12:21 AM

Still no sucess,

The clear o-ring inside the air chamber poped out so i put it back in and lubed up the bolt a bit,

Now it only leaks slightly and wont fire.

Any ideas at all guys.
0

#14 User is offline   jim762 

  • Forum Member
  • PipPip
  • Group: Members
  • Posts: 171
  • Joined: 30-September 08
  • Gender:Male
  • Location:lemoore, Ca
  • Brigade Name:jim762

Posted 27 January 2009 - 02:43 AM

Check out the tiberius forum, might find an answer there.....http://forums.tiberiusarms.com/

May God have mercy upon my enemies, because I won't!
Sponsored by: Urban Ops Armory
0

#15 User is offline   joshnz 

  • Forum Newbie
  • Pip
  • Group: Members
  • Posts: 8
  • Joined: 26-January 09

Posted 27 January 2009 - 06:41 PM

Hey thought i would post my solution so that others can know.

What had happend was the bolt had got to dry and had started to stick and as a result the o-ring between the air chamber and the bolt came out and broke.

So i replaced that o-ring with one from the hardware shop and got some metal polish, polished the bolt, lubed it up and it back together and all done ^_^

Working once again.
0

Share this topic:


  • (2 Pages)
  • +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users