Special Ops Paintball: rhino bed lining - Special Ops Paintball

Jump to content


  • (2 Pages)
  • +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

rhino bed lining Rate Topic: -----

#16 User is offline   youwish959 

  • Baghdad Bob
  • PipPipPip
  • Group: Members
  • Posts: 625
  • Joined: 25-January 05
  • Gender:Male
  • Brigade Name:Youwish959

Posted 28 September 2005 - 01:21 PM

Evil Fingers, on Sep 28 2005, 01:01 PM, said:

bigguy, on Sep 27 2005, 07:13 PM, said:

yeah about that...how do i mask my gun properly

Take the marker apart and remove all the internals, get masking tape and cover all the holes from the inside, the tape will prevent any overspray from getting onto the inner walls of the marker.

That was exactly what I was thinking.
0

#17 User is offline   evillepaintball 

  • You won't do it! You ain't crazy!
  • PipPipPip
  • Group: Members
  • Posts: 576
  • Joined: 25-February 05
  • Gender:Male
  • Location:Evansville Indiana
  • Brigade Name:sunshine ac-05

Posted 28 September 2005 - 07:22 PM

and dont forget to put somethin in the screwholes to protect your threads, rhino lining would def. do some crap to them
"it just doesnt look cool unless you're riding a yamazuki zx1200rrr" - C9H13NO3
0

#18 User is offline   youwish959 

  • Baghdad Bob
  • PipPipPip
  • Group: Members
  • Posts: 625
  • Joined: 25-January 05
  • Gender:Male
  • Brigade Name:Youwish959

Posted 28 September 2005 - 08:58 PM

I think I might do this to my marker.
0

#19 User is offline   sartek 

  • Trained Shop Monkey
  • PipPipPipPipPip
  • Group: Members
  • Posts: 1,651
  • Joined: 15-April 05
  • Gender:Male
  • Location:Portland, OR
  • Brigade Name:SARTEK

Posted 28 September 2005 - 10:51 PM

I'm not sure if you guys realize this.. Rhino lining is a spray on polyurethane coating that expands as it cures. it has to be sprayed on using an airless sprayer, and it doesn't come in a spraycan. It also has to be sprayed onto bare metal. as for masking off the bolt holes, etc.. I would put some longer screws into the holes to prevent the spray from getting into the holes. as for the cocking hole in the 98, once it's sprayed over the masking, you would have to cut out the section for the cocking pin.
"I tinker, therefore I am" - Doc Nickel
DOT HazMat Geek, Airsmith, Tinkerer
0

#20 User is offline   Evil Fingers 

  • ELITE Member
  • PipPipPipPipPipPipPip
  • Group: Members
  • Posts: 13,979
  • Joined: 22-September 06
  • Location:Sucka Free, Nor Cal

Posted 29 September 2005 - 01:04 AM

sartek, on Sep 28 2005, 09:51 PM, said:

I'm not sure if you guys realize this.. Rhino lining is a spray on polyurethane coating that expands as it cures. it has to be sprayed on using an airless sprayer, and it doesn't come in a spraycan. It also has to be sprayed onto bare metal. as for masking off the bolt holes, etc.. I would put some longer screws into the holes to prevent the spray from getting into the holes. as for the cocking hole in the 98, once it's sprayed over the masking, you would have to cut out the section for the cocking pin.

Spraying Rhino Liner is only done on a large area, like the bed a of a pick up truck but, you can apply it wit a paint brush or a paint roller.
0

Share this topic:


  • (2 Pages)
  • +
  • 1
  • 2
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users